The unique design of the CLAM trap enables a replaceable valve and seat selection within the body of each model, and a range of valves and seats universally interchangeable in the bodies of all MK7 series traps.<\/p>\n\n\n\n
Advantages To The Engineer Are:<\/p>\n\n\n\n
Model<\/p>\n\n\n\n
Body Material<\/p>\n\n\n\n
Operating Pressures & Temperatures<\/p>\n\n\n\n
Valve Sets Available<\/p>\n\n\n\n
Comment<\/p>\n<\/div>\n\n\n\n
MK2<\/p>\n\n\n\n
Forged brass<\/p>\n\n\n\n
35-1720 kPa
at 208\u00b0C<\/p>\n\n\n\n
A3<\/p>\n\n\n\n
A smaller trap for general purpose, jacketed and tracer line applications.<\/p>\n<\/div>\n\n\n\n
MK7B<\/p>\n\n\n\n
Bronze<\/p>\n\n\n\n
35-1724 kPa
at 260\u00b0C<\/p>\n\n\n\n
C2, D2, G2, G2L<\/p>\n\n\n\n
Corrosion resistant to most contaminated condensate and corrosive atmospheres.<\/p>\n<\/div>\n\n\n\n
MK7C<\/p>\n\n\n\n
A105 Forged steel<\/p>\n\n\n\n
35-4137 kPa
at 400\u00b0C<\/p>\n\n\n\n
C2, D2, G2, G2L<\/p>\n\n\n\n
Maximum variety of end connections.
For higher pressure services.<\/p>\n<\/div>\n\n\n\n
MK7C\/ 1000<\/p>\n\n\n\n
F11 Forged chrome moly steel<\/p>\n\n\n\n
3103-8618kPa
at 566\u00b0C<\/p>\n\n\n\n
G3, J3<\/p>\n\n\n\n
Solves high pressure drainage problems Successfully.<\/p>\n<\/div>\n\n\n\n
MK10B<\/p>\n\n\n\n
Cast chrome moly steel<\/p>\n\n\n\n
35-3103 kPa
at 343\u00b0C<\/p>\n\n\n\n
F2, K2<\/p>\n\n\n\n
The largest CLAM trap for use where extreme condensate discharge rates are encountered<\/p>\n<\/div>\n<\/div>\n\n\n\n
A3<\/p>\n\n\n\n
Fitted to MK2 general purpose traps for pressures from 35-1720 kPa where compactness and light weight is important.
Low capacity by general CLAM standards.<\/p>\n<\/div>\n\n\n\n
C2<\/p>\n\n\n\n
Low pressure, high volume condensate and air discharge.<\/p>\n<\/div>\n\n\n\n
D2<\/p>\n\n\n\n
Most commonly used valve and seat, because of applicable pressure range 35-1034 kPa.
Do not use over 1034 kPa unless condensate capacity demands.
Very high air discharge rating.<\/p>\n<\/div>\n\n\n\n
G2<\/p>\n\n\n\n
For pressures in the 1034 to 4137 kPa range.
May be used for higher pressures when extra capacity is required.
Do not use below 1034 kPa or air-locking may occur.<\/p>\n<\/div>\n\n\n\n
G2-L<\/p>\n\n\n\n
Low to medium capacity for pressures to 1034 kPa.
High air purging and fast heat-up capability.<\/p>\n<\/div>\n\n\n\n
J3<\/p>\n\n\n\n
For high pressure and super heat service to 10340 kPa and temperatures to 566\u00b0C.
Application-Turbine Manifold and main line drainage.
Fitted to MK7C and MK7C\/1000 traps only.
Do not use below 3100 kPa or air-locking may occur.<\/p>\n<\/div>\n\n\n\n
G3<\/p>\n\n\n\n
Greater discharge capacity than the J3<\/p>\n<\/div>\n\n\n\n
K2<\/p>\n\n\n\n
Fitted to MK10B trap only for pressures from 35-3100 kPa.
Capacity rating of thousands of kgs per hour.<\/p>\n<\/div>\n\n\n\n